The INJECT ACRYL ELASTIC R system is a non-toxic aqueous solution of multifunctional methacrylates.
DESCRIPTION
The compound gels in a few seconds to a few minutes when an activator or initiator is added just before use. The final product is a soft and tacky cros-slinked gel. In wet or dry conditions, the volume of the gel increases or decreases in a reversible manner assuring perfect waterproofing.
USE
The INJECT ACRYL ELASTIC R is used for sealing and consolidation works in presence of water.
The substance is injected through packers or injection hoses. or injection hoses.
The low viscosity of the product assures high fluidity.
It’s a hydrophilic system with a controlled set time used in the following applications:
Treatment of water infiltration and ground water ingress;
Treatment of soils;
Treatment of voids and cavities, in the form of sand grouts;
Injection of water bearing cracks in concrete or masonry walls;
The INJECT ACRYL B system is a non-toxic aqueous solution of multifunctional methacrylates.
DESCRIPTION
The compound gels in a few seconds to a few minutes when an activator or initiator is added just before use.
The final product is a soft and tacky cros-slinked gel.
In wet or dry conditions, the volume of the gel increases or decreases in a reversible manner assuring perfect waterproofing.
USE
The INJECT ACRYL B system is used for sealing and consolidation works in presence of water. The substance is injected through packers or injection hoses. The low viscosity of the product assures high fluidity. It’s a hydrophilic system with a controlled set time used in the following applications :
Treatment of water infiltration and ground water ingress;
Treatment of soils;
Treatment of voids and cavities, in the form of sand grouts;
Injection of water bearing cracks in concrete or masonry walls;
For grout injection hoses use the INJECT ACRYL ELASTIC R system.
Single component, transparent, non-yellowing, elastic polyurethane coating with RAL of your choice.
DESCRIPTION
POLIUPLAN RIV is a totally aliphatic single-component polyurethane for waterproofing and protection.
It produces a shiny, transparent non-yellowing membrane with excellent mechanical and elastic properties.
POLIUPLAN RIVis ideal both for the protection of the products in the POLIUPLAN range in intense transit areas (pigmented with a small amount of POLIUPLAN) and as a final protective layer in flooring applications.
USE
As a final (pigmented) coating for POLIUPLAN.
For protection on concrete or other synthetic coverings;
POLIUPLAN PRIMER is a two-component water-based epoxy paint.
DESCRIPTION
POLIUPLAN PRIMER is a two-component water-based epoxy paint, with more than twenty years of successful use. It is used as a primer for POLIUPLAN and for all polyurethane-based products. POLIUPLAN PRIMERis the ideal primer (or first layer) in all applications with problems of negative pressure and rising damp. It is simple and safe to apply (zero VOC) and has numerous applications beyond its use as a primer.
USE
Primer for any system: Epoxies, Polyurethanes etc.;
Single-component injection polyurethane resin, solvent-free, injected with a two-component pump, with water as the second component.. INJECT IDRO consists of solvent-free isocyanate, based on diphenylmethanediisocyanate and reacts only if in contact with water. In a polymer-water ratio varying from 1:1 to 1:7 it forms a compact and waterproof elastomer foam. In a polymer-water ratio varying from 1:9 to 1:15 it forms a very elastic elastomer gel. Applied correctly, INJECT IDRO adheres to the surface forming a rubbery, resistant and very elastic seal, which immediately blocks any water.
Single-component, solvent-free, injection polyurethane resin, ideal for dynamic cracks and damp joints due to water infiltration. The reaction with water produces a flexible polyurethane foam with closed cells. The end product, injected under pressure, does not shrink or swell. In a short time a good compression force is obtained. Better to inject the resin with a certain counter pressure. The reaction rate can be easily adapted by varying the accelerator or catalyst content from 6% to 10%. The more catalyst is added, the higher the reaction rate.
CASE STUDIES
ALTARE (SV)
Etruscan Glassworks, Water ingress sealing
VARAZZE(SV)
Residential Building – Water ingress sealing elevator pits
Single-component, solvent-free, injection polyurethane resin, ideal for dynamic cracks and damp joints due to water infiltration. Its reaction with water produces a semi-flexible polyurethane foam. The formation of CO2 allows the foam to penetrate deeply into the cracks. The end product does not shrink or swell. In a short time a good compression force is obtained. The reaction rate can be easily adapted by varying the accelerator or catalyst content from 6% to 10%. The more catalyst is added, the higher the reaction rate.
Transparent elastic polyurethane liquid membrane for continuous waterproofing.
DESCRIPTION
POLIUPLAN T is a transparent membrane in single-component polyurethane, aliphatic, with good elasticity and with a high content of dry residue, used for long-lasting waterproofing. Thanks to its aliphatic structure, POLIUPLAN Tis UV stable, so it does not yellow over time. It is resistant to chemical and physical aggression. It is mainly used for highly reliable transparent waterproofing.
USE
POLIUPLAN Tis a low viscosity product ideal for use as a transparent membrane to be applied as a protection for products from the waterproofing line by System Technology. POLIUPLAN T is also used as a transparent binder resin for floor coverings especially in applications where flexibility and UV stability are required. POLIUPLAN T uses an exclusive hardening system (activated by humidity) and unlike other systems it does not form bubbles.
POLIUPLAN LC is a premium, liquid and cold-applied, one-part polyurethane waterproofing membrane. It cures by reaction woth ambient moisture to form a strong protective and self-levelling base. POLIUPLAN LC is based on LC-Technology, developed to avoid polymerization bubbles present in traditional polyurethane. LC-Technology combines the best polyurethane properties with a very low emission and bubble-free system.
One component
Odorless
Neutral curing, does not stain, corrode or affect concrete
Liquid: easy to apply with professional or simple tools, like brush or roller
Cold applied: in any situation and any climate
Full surface adhesion and seamless covering, even on curved surfaces
In combination with non-woven fabric is suitable to cover details, corners, edges
Utilizziamo i cookie sul nostro sito Web per offrirti l'esperienza più pertinente ricordando le tue preferenze e le visite ripetute. Cliccando su “Accetta” acconsenti all'uso dei cookie NECESSARI, e di quelli FACOLTATIVI da te GESTIBILI dal pulsante "Selezione Cookie".
Questo sito utilizza i cookie per migliorare la tua esperienza durante la navigazione nel sito. Di questi, i cookie classificati come NECESSARI vengono memorizzati nel browser in quanto sono essenziali per il funzionamento delle funzionalità di base del sito web. Utilizziamo anche altri cookie che ci aiutano ad analizzare e capire come utilizzi questo sito web. Questi altri cookie SWONO DISATTIVI PER IMPOSTAZIONE PREDEFINITA e verranno memorizzati nel tuo browser solo con il tuo consenso. Hai anche la possibilità di attivare/disattivare questi cookie. Tuttavia, la disattivazione di alcuni di questi cookie potrebbe influire sulla tua esperienza di navigazione.
